View MLG0603P47NJT000_8402833.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

inductors february 2015 multilayer ceramic mlg0603p 0603 [0201 inch]* * dimensions code jis[eia] inductors for high frequency circuits mlg0603p ty p e mlg-p series
(2/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 12 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 7 5% rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. inductors for high frequency circuits multilayer ceramic features high q type inductor for high-frequency circuits. inductance range: from 0.6 to 120nh. 0.1n step inductance lineup. compared with existing products, the size was greatly re duced, making it opti mal for fine-pitch circuits. optimal configuration that greatly improves the q to 800mhz or higher. advanced monolithic structure is formed us ing a multilayering and sintering process wi th ceramic and conductive materials for h igh- frequency. application smart phones, tablet terminals, high frequency modules (pas, vcos, fems , etc.), bluetooth, w-lan, uwb, tuners and other high frequency circuits for the mobile communication industry part number construction operating temperature range, pack age quantity, product weight the storage temperature range is for after the circuit board is mounted. product compatible with rohs directive halogen-free compatible with lead-free solders overview of mlg0603p type mlg 0603 p 0n6 b t 000 series name lwh dimensions characteristics inductance inductance tolerance packaging style internal code (mm) (nh) 0603 0.60.30.3 p 1n1 1.1 b 0.1nh t taping 000 11n 11 c 0.2nh s 0.3nh h3% j5% type temperature range package quantity individual weight operating temperature c storage temperature c (pieces/reel) mg mlg0603p C55 to +125 C55 to +125 15000 0.2 rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://produ ct.tdk.com/en/environment/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm.
(4/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 30 to 60s 250 to 260c 10s max. natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type shape & dimensions recommended land pattern dimensions in mm 0.150.05 0.150.05 0.600.03 0.090.04 0.090.04 0.300.03 0.300.03 dimensions in mm 0.3 0.3 0.25 0.25
(6/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type electrical characteristics characteristics specification table please contact us for information on inductance tolerance, g (2%). ~ short bar residual inductance =0.43nh measurement equipment ? equivalent measurement equipment may be used. l q l, q measuring frequency self-resonant frequency dc resistance rated current part no. (nh) tolerance min. (mhz) (ghz)min. (ghz)typ. ( )max. ( )typ. (ma)max. 0.6 0.1nh 500 10.0 20.0 0.06 0.01 1000 mlg0603p0n6bt000 0.6 0.2nh 500 10.0 20.0 0.06 0.01 1000 mlg0603p0n6ct000 0.7 0.1nh 500 10.0 20.0 0.06 0.01 1000 mlg0603p0n7bt000 0.7 0.2nh 500 10.0 20.0 0.06 0.01 1000 mlg0603p0n7ct000 0.8 0.1nh 500 10.0 20.0 0.06 0.02 1000 mlg0603p0n8bt000 0.8 0.2nh 500 10.0 20.0 0.06 0.02 1000 mlg0603p0n8ct000 0.9 0.1nh 500 10.0 20.0 0.06 0.02 1000 mlg0603p0n9bt000 0.9 0.2nh 500 10.0 20.0 0.06 0.02 1000 mlg0603p0n9ct000 1.0 0.3nh 14 500 10.0 20.0 0.07 0.02 1000 mlg0603p1n0st000 1.0 0.1nh 14 500 10.0 20.0 0.07 0.02 1000 mlg0603p1n0bt000 1.0 0.2nh 14 500 10.0 20.0 0.07 0.02 1000 mlg0603p1n0ct000 1.1 0.3nh 14 500 10.0 19.9 0.07 0.03 1000 mlg0603p1n1st000 1.1 0.1nh 14 500 10.0 19.9 0.07 0.03 1000 mlg0603p1n1bt000 1.1 0.2nh 14 500 10.0 19.9 0.07 0.03 1000 mlg0603p1n1ct000 1.2 0.3nh 14 500 10.0 16.0 0.08 0.04 800 mlg0603p1n2st000 1.2 0.1nh 14 500 10.0 16.0 0.08 0.04 800 mlg0603p1n2bt000 1.2 0.2nh 14 500 10.0 16.0 0.08 0.04 800 mlg0603p1n2ct000 1.3 0.3nh 14 500 10.0 13.9 0.08 0.03 800 mlg0603p1n3st000 1.3 0.1nh 14 500 10.0 13.9 0.08 0.03 800 mlg0603p1n3bt000 1.3 0.2nh 14 500 10.0 13.9 0.08 0.03 800 mlg0603p1n3ct000 1.4 0.3nh 14 500 10.0 11.7 0.09 0.04 800 mlg0603p1n4st000 1.4 0.1nh 14 500 10.0 11.7 0.09 0.04 800 mlg0603p1n4bt000 1.4 0.2nh 14 500 10.0 11.7 0.09 0.04 800 mlg0603p1n4ct000 1.5 0.3nh 14 500 10.0 14.9 0.10 0.03 800 mlg0603p1n5st000 1.5 0.1nh 14 500 10.0 14.9 0.10 0.03 800 mlg0603p1n5bt000 1.5 0.2nh 14 500 10.0 14.9 0.10 0.03 800 mlg0603p1n5ct000 1.6 0.3nh 14 500 10.0 13.4 0.10 0.03 700 mlg0603p1n6st000 1.6 0.1nh 14 500 10.0 13.4 0.10 0.03 700 mlg0603p1n6bt000 1.6 0.2nh 14 500 10.0 13.4 0.10 0.03 700 mlg0603p1n6ct000 1.7 0.3nh 14 500 10.0 12.8 0.10 0.02 700 mlg0603p1n7st000 1.7 0.1nh 14 500 10.0 12.8 0.10 0.02 700 mlg0603p1n7bt000 1.7 0.2nh 14 500 10.0 12.8 0.10 0.02 700 mlg0603p1n7ct000 1.8 0.3nh 14 500 9.0 10.7 0.10 0.03 700 mlg0603p1n8st000 1.8 0.1nh 14 500 9.0 10.7 0.10 0.03 700 mlg0603p1n8bt000 1.8 0.2nh 14 500 9.0 10.7 0.10 0.03 700 mlg0603p1n8ct000 1.9 0.3nh 14 500 9.0 10.9 0.10 0.04 600 mlg0603p1n9st000 1.9 0.1nh 14 500 9.0 10.9 0.10 0.04 600 mlg0603p1n9bt000 1.9 0.2nh 14 500 9.0 10.9 0.10 0.04 600 mlg0603p1n9ct000 2.0 0.3nh 14 500 8.5 10.1 0.10 0.03 600 mlg0603p2n0st000 2.0 0.1nh 14 500 8.5 10.1 0.10 0.03 600 mlg0603p2n0bt000 2.0 0.2nh 14 500 8.5 10.1 0.10 0.03 600 mlg0603p2n0ct000 2.1 0.3nh 14 500 8.0 9.8 0.10 0.05 600 mlg0603p2n1st000 2.1 0.1nh 14 500 8.0 9.8 0.10 0.05 600 mlg0603p2n1bt000 2.1 0.2nh 14 500 8.0 9.8 0.10 0.05 600 mlg0603p2n1ct000 measurement item product no. manufacturer l, q 4291b+16197a agilent technologies self-resonant frequency 8720c agilent technologies dc resistance type-7561 yokogawa
(7/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type electrical characteristics characteristics specification table please contact us for information on inductance tolerance, g (2%). ~ short bar residual inductance =0.43nh measurement equipment ? equivalent measurement equipment may be used. l q l, q measuring frequency self-resonant frequency dc resistance rated current part no. (nh) tolerance min. (mhz) (ghz)min. (ghz)typ. ( )max. ( )typ. (ma)max. 2.2 0.3nh 14 500 7.5 9.0 0.10 0.07 600 mlg0603p2n2st000 2.2 0.1nh 14 500 7.5 9.0 0.10 0.07 600 mlg0603p2n2bt000 2.2 0.2nh 14 500 7.5 9.0 0.10 0.07 600 mlg0603p2n2ct000 2.3 0.3nh 14 500 7.5 8.4 0.20 0.07 600 mlg0603p2n3st000 2.3 0.1nh 14 500 7.5 8.4 0.20 0.07 600 mlg0603p2n3bt000 2.3 0.2nh 14 500 7.5 8.4 0.20 0.07 600 mlg0603p2n3ct000 2.4 0.3nh 14 500 7.5 10.9 0.20 0.12 500 mlg0603p2n4st000 2.4 0.1nh 14 500 7.5 10.9 0.20 0.12 500 mlg0603p2n4bt000 2.4 0.2nh 14 500 7.5 10.9 0.20 0.12 500 mlg0603p2n4ct000 2.5 0.3nh 14 500 7.5 9.9 0.20 0.09 500 mlg0603p2n5st000 2.5 0.1nh 14 500 7.5 9.9 0.20 0.09 500 mlg0603p2n5bt000 2.5 0.2nh 14 500 7.5 9.9 0.20 0.09 500 mlg0603p2n5ct000 2.6 0.3nh 14 500 7.5 10.1 0.20 0.14 500 mlg0603p2n6st000 2.6 0.1nh 14 500 7.5 10.1 0.20 0.14 500 mlg0603p2n6bt000 2.6 0.2nh 14 500 7.5 10.1 0.20 0.14 500 mlg0603p2n6ct000 2.7 0.3nh 14 500 7.5 10.0 0.20 0.14 500 mlg0603p2n7st000 2.7 0.1nh 14 500 7.5 10.0 0.20 0.14 500 mlg0603p2n7bt000 2.7 0.2nh 14 500 7.5 10.0 0.20 0.14 500 mlg0603p2n7ct000 2.8 0.3nh 14 500 7.5 9.9 0.20 0.10 500 mlg0603p2n8st000 2.8 0.1nh 14 500 7.5 9.9 0.20 0.10 500 mlg0603p2n8bt000 2.8 0.2nh 14 500 7.5 9.9 0.20 0.10 500 mlg0603p2n8ct000 2.9 0.3nh 14 500 7.5 9.2 0.20 0.10 500 mlg0603p2n9st000 2.9 0.1nh 14 500 7.5 9.2 0.20 0.10 500 mlg0603p2n9bt000 2.9 0.2nh 14 500 7.5 9.2 0.20 0.10 500 mlg0603p2n9ct000 3.0 0.3nh 14 500 7.5 9.1 0.20 0.14 450 mlg0603p3n0st000 3.0 0.1nh 14 500 7.5 9.1 0.20 0.14 450 mlg0603p3n0bt000 3.0 0.2nh 14 500 7.5 9.1 0.20 0.14 450 mlg0603p3n0ct000 3.1 0.3nh 14 500 7.5 8.8 0.20 0.10 450 mlg0603p3n1st000 3.1 0.1nh 14 500 7.5 8.8 0.20 0.10 450 mlg0603p3n1bt000 3.1 0.2nh 14 500 7.5 8.8 0.20 0.10 450 mlg0603p3n1ct000 3.2 0.3nh 14 500 7.5 8.4 0.20 0.14 450 mlg0603p3n2st000 3.2 0.1nh 14 500 7.5 8.4 0.20 0.14 450 mlg0603p3n2bt000 3.2 0.2nh 14 500 7.5 8.4 0.20 0.14 450 mlg0603p3n2ct000 3.3 0.3nh 14 500 7.5 8.4 0.20 0.13 450 mlg0603p3n3st000 3.3 0.1nh 14 500 7.5 8.4 0.20 0.13 450 mlg0603p3n3bt000 3.3 0.2nh 14 500 7.5 8.4 0.20 0.13 450 mlg0603p3n3ct000 3.4 0.3nh 14 500 7.0 8.1 0.20 0.13 450 mlg0603p3n4st000 3.4 0.1nh 14 500 7.0 8.1 0.20 0.13 450 mlg0603p3n4bt000 3.4 0.2nh 14 500 7.0 8.1 0.20 0.13 450 mlg0603p3n4ct000 3.5 0.3nh 14 500 6.5 8.0 0.20 0.12 450 mlg0603p3n5st000 3.5 0.1nh 14 500 6.5 8.0 0.20 0.12 450 mlg0603p3n5bt000 3.5 0.2nh 14 500 6.5 8.0 0.20 0.12 450 mlg0603p3n5ct000 3.6 0.3nh 14 500 6.5 7.7 0.20 0.10 400 mlg0603p3n6st000 3.6 0.1nh 14 500 6.5 7.7 0.20 0.10 400 mlg0603p3n6bt000 3.6 0.2nh 14 500 6.5 7.7 0.20 0.10 400 mlg0603p3n6ct000 measurement item product no. manufacturer l, q 4291b+16197a agilent technologies self-resonant frequency 8720c agilent technologies dc resistance type-7561 yokogawa
(8/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type electrical characteristics characteristics specification table please contact us for information on inductance tolerance, g (2%). ~ short bar residual inductance =0.43nh measurement equipment ? equivalent measurement equipment may be used. l q l, q measuring frequency self-resonant frequency dc resistance rated current part no. (nh) tolerance min. (mhz) (ghz)min. (ghz)typ. ( )max. ( )typ. (ma)max. 3.7 0.3nh 14 500 6.5 7.4 0.20 0.14 400 mlg0603p3n7st000 3.7 0.1nh 14 500 6.5 7.4 0.20 0.14 400 mlg0603p3n7bt000 3.7 0.2nh 14 500 6.5 7.4 0.20 0.14 400 mlg0603p3n7ct000 3.8 0.3nh 14 500 5.8 7.0 0.30 0.24 400 mlg0603p3n8st000 3.8 0.1nh 14 500 5.8 7.0 0.30 0.24 400 mlg0603p3n8bt000 3.8 0.2nh 14 500 5.8 7.0 0.30 0.24 400 mlg0603p3n8ct000 3.9 0.3nh 14 500 5.8 7.1 0.30 0.22 400 mlg0603p3n9st000 3.9 0.1nh 14 500 5.8 7.1 0.30 0.22 400 mlg0603p3n9bt000 3.9 0.2nh 14 500 5.8 7.1 0.30 0.22 400 mlg0603p3n9ct000 4.0 0.3nh 14 500 5.8 6.7 0.40 0.21 350 mlg0603p4n0st000 4.0 0.1nh 14 500 5.8 6.7 0.40 0.21 350 mlg0603p4n0bt000 4.0 0.2nh 14 500 5.8 6.7 0.40 0.21 350 mlg0603p4n0ct000 4.1 0.3nh 14 500 5.8 6.7 0.40 0.29 350 mlg0603p4n1st000 4.1 0.1nh 14 500 5.8 6.7 0.40 0.29 350 mlg0603p4n1bt000 4.1 0.2nh 14 500 5.8 6.7 0.40 0.29 350 mlg0603p4n1ct000 4.2 0.3nh 14 500 5.8 6.6 0.40 0.24 350 mlg0603p4n2st000 4.2 0.1nh 14 500 5.8 6.6 0.40 0.24 350 mlg0603p4n2bt000 4.2 0.2nh 14 500 5.8 6.6 0.40 0.24 350 mlg0603p4n2ct000 4.3 0.3nh 14 500 5.8 6.7 0.40 0.24 350 mlg0603p4n3st000 4.3 3% 14 500 5.8 6.7 0.40 0.24 350 mlg0603p4n3ht000 4.3 5% 14 500 5.8 6.7 0.40 0.24 350 mlg0603p4n3jt000 4.7 0.3nh 14 500 5.5 6.9 0.40 0.16 350 mlg0603p4n7st000 4.7 3% 14 500 5.5 6.9 0.40 0.16 350 mlg0603p4n7ht000 4.7 5% 14 500 5.5 6.9 0.40 0.16 350 mlg0603p4n7jt000 5.1 0.3nh 14 500 5.5 6.6 0.40 0.30 350 mlg0603p5n1st000 5.1 3% 14 500 5.5 6.6 0.40 0.30 350 mlg0603p5n1ht000 5.1 5% 14 500 5.5 6.6 0.40 0.30 350 mlg0603p5n1jt000 5.6 0.3nh 14 500 4.0 5.3 0.40 0.32 350 mlg0603p5n6st000 5.6 3% 14 500 4.0 5.3 0.40 0.32 350 mlg0603p5n6ht000 5.6 5% 14 500 4.0 5.3 0.40 0.32 350 mlg0603p5n6jt000 6.2 0.3nh 14 500 4.0 6.3 0.70 0.59 300 mlg0603p6n2st000 6.2 3% 14 500 4.0 6.3 0.70 0.59 300 mlg0603p6n2ht000 6.2 5% 14 500 4.0 6.3 0.70 0.59 300 mlg0603p6n2jt000 6.8 3% 14 500 4.0 6.1 0.75 0.62 300 mlg0603p6n8ht000 6.8 5% 14 500 4.0 6.1 0.75 0.62 300 mlg0603p6n8jt000 7.5 3% 14 500 4.0 5.4 0.80 0.70 300 mlg0603p7n5ht000 7.5 5% 14 500 4.0 5.4 0.80 0.70 300 mlg0603p7n5jt000 8.2 3% 14 500 4.0 5.2 0.85 0.71 250 mlg0603p8n2ht000 8.2 5% 14 500 4.0 5.2 0.85 0.71 250 mlg0603p8n2jt000 9.1 3% 14 500 4.0 5.0 0.90 0.76 250 mlg0603p9n1ht000 9.1 5% 14 500 4.0 5.0 0.90 0.76 250 mlg0603p9n1jt000 10.0 3% 14 500 4.0 4.7 0.95 0.85 250 mlg0603p10nht000 10.0 5% 14 500 4.0 4.7 0.95 0.85 250 mlg0603p10njt000 11.0 3% 14 500 3.5 4.5 1.00 0.64 250 mlg0603p11nht000 11.0 5% 14 500 3.5 4.5 1.00 0.64 250 mlg0603p11njt000 measurement item product no. manufacturer l, q 4291b+16197a agilent technologies self-resonant frequency 8720c agilent technologies dc resistance type-7561 yokogawa
(9/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type electrical characteristics characteristics specification table please contact us for information on inductance tolerance, g (2%). ~ short bar residual inductance =0.43nh measurement equipment ? equivalent measurement equipment may be used. l q l, q measuring frequency self-resonant frequency dc resistance rated current part no. (nh) tolerance min. (mhz) (ghz)min. (ghz)typ. ( )max. ( )typ. (ma)max. 12.0 3% 14 500 3.5 4.3 1.10 0.82 250 mlg0603p12nht000 12.0 5% 14 500 3.5 4.3 1.10 0.82 250 mlg0603p12njt000 13.0 3% 14 500 3.2 4.2 1.10 0.87 250 mlg0603p13nht000 13.0 5% 14 500 3.2 4.2 1.10 0.87 250 mlg0603p13njt000 15.0 3% 14 500 3.2 3.7 1.20 0.94 250 mlg0603p15nht000 15.0 5% 14 500 3.2 3.7 1.20 0.94 250 mlg0603p15njt000 16.0 3% 14 500 3.0 3.6 1.20 1.00 200 mlg0603p16nht000 16.0 5% 14 500 3.0 3.6 1.20 1.00 200 mlg0603p16njt000 18.0 3% 14 500 3.0 3.5 1.40 1.04 200 mlg0603p18nht000 18.0 5% 14 500 3.0 3.5 1.40 1.04 200 mlg0603p18njt000 20.0 3% 14 500 2.2 3.3 1.90 1.33 150 mlg0603p20nht000 20.0 5% 14 500 2.2 3.3 1.90 1.33 150 mlg0603p20njt000 22.0 3% 14 500 2.2 2.9 1.90 1.31 150 mlg0603p22nht000 22.0 5% 14 500 2.2 2.9 1.90 1.31 150 mlg0603p22njt000 24.0 3% 14 500 2.2 2.9 2.10 1.17 140 mlg0603p24nht000 24.0 5% 14 500 2.2 2.9 2.10 1.17 140 mlg0603p24njt000 27.0 3% 14 500 2.2 2.7 2.10 1.45 140 mlg0603p27nht000 27.0 5% 14 500 2.2 2.7 2.10 1.45 140 mlg0603p27njt000 30.0 3% 10 300 1.8 2.3 2.20 1.37 130 mlg0603p30nht000 30.0 5% 10 300 1.8 2.3 2.20 1.37 130 mlg0603p30njt000 33.0 3% 10 300 1.8 2.4 2.20 1.55 130 mlg0603p33nht000 33.0 5% 10 300 1.8 2.4 2.20 1.55 130 mlg0603p33njt000 36.0 3% 10 300 1.8 2.2 2.40 1.49 120 mlg0603p36nht000 36.0 5% 10 300 1.8 2.2 2.40 1.49 120 mlg0603p36njt000 39.0 3% 10 300 1.8 2.2 2.40 1.72 120 mlg0603p39nht000 39.0 5% 10 300 1.8 2.2 2.40 1.72 120 mlg0603p39njt000 43.0 3% 10 300 1.6 2.0 2.90 1.61 110 mlg0603p43nht000 43.0 5% 10 300 1.6 2.0 2.90 1.61 110 mlg0603p43njt000 47.0 3% 10 300 1.6 2.0 2.90 2.18 110 mlg0603p47nht000 47.0 5% 10 300 1.6 2.0 2.90 2.18 110 MLG0603P47NJT000 51.0 3% 10 300 1.4 1.9 3.50 1.87 100 mlg0603p51nht000 51.0 5% 10 300 1.4 1.9 3.50 1.87 100 mlg0603p51njt000 56.0 3% 10 300 1.4 1.8 3.50 2.35 100 mlg0603p56nht000 56.0 5% 10 300 1.4 1.8 3.50 2.35 100 mlg0603p56njt000 62.0 3% 10 300 1.2 1.6 3.50 2.12 100 mlg0603p62nht000 62.0 5% 10 300 1.2 1.6 3.50 2.12 100 mlg0603p62njt000 68.0 3% 9 300 1.2 1.6 3.50 2.69 100 mlg0603p68nht000 68.0 5% 9 300 1.2 1.6 3.50 2.69 100 mlg0603p68njt000 75.0 3% 9 300 1.0 1.5 4.00 2.59 80 mlg0603p75nht000 75.0 5% 9 300 1.0 1.5 4.00 2.59 80 mlg0603p75njt000 82.0 3% 9 300 1.0 1.5 4.00 2.71 80 mlg0603p82nht000 82.0 5% 9 300 1.0 1.5 4.00 2.71 80 mlg0603p82njt000 91.0 3% 9 300 0.9 1.3 4.50 2.92 80 mlg0603p91nht000 91.0 5% 9 300 0.9 1.3 4.50 2.92 80 mlg0603p91njt000 measurement item product no. manufacturer l, q 4291b+16197a agilent technologies self-resonant frequency 8720c agilent technologies dc resistance type-7561 yokogawa
(10/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type electrical characteristics characteristics specification table please contact us for information on inductance tolerance, g (2%). ~ short bar residual inductance =0.43nh measurement equipment ? equivalent measurement equipment may be used. l q l, q measuring frequency self-resonant frequency dc resistance rated current part no. (nh) tolerance min. (mhz) (ghz)min. (ghz)typ. ( )max. ( )typ. (ma)max. 100.0 3% 9 300 0.9 1.3 4.50 3.20 80 mlg0603pr10ht000 100.0 5% 9 300 0.9 1.3 4.50 3.20 80 mlg0603pr10jt000 110.0 3% 9 300 0.8 1.1 5.00 3.50 80 mlg0603pr11ht000 110.0 5% 9 300 0.8 1.1 5.00 3.50 80 mlg0603pr11jt000 120.0 3% 9 300 0.8 1.0 5.00 3.79 80 mlg0603pr12ht000 120.0 5% 9 300 0.8 1.0 5.00 3.79 80 mlg0603pr12jt000 measurement item product no. manufacturer l, q 4291b+16197a agilent technologies self-resonant frequency 8720c agilent technologies dc resistance type-7561 yokogawa
(11/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type electrical characteristics l, q frequency characteristics table please contact us for information on inductance tolerance, g (2%). measurement equipment ? equivalent measurement equipment may be used. l(nh)typ. q typ. part no. 500mhz 800mhz 1.8ghz 2.0ghz 2.4ghz 500mhz 800mhz 1.8ghz 2.0ghz 2.4ghz 0.6 0.6 0.6 0.6 0.6 16min. 22min. 35min. 37min. 41min. mlg0603p0n6bt000 0.6 0.6 0.6 0.6 0.6 16min. 22min. 35min. 37min. 41min. mlg0603p0n6ct000 0.7 0.7 0.7 0.7 0.7 16min. 22min. 35min. 37min. 41min. mlg0603p0n7bt000 0.7 0.7 0.7 0.7 0.7 16min. 22min. 35min. 37min. 41min. mlg0603p0n7ct000 0.8 0.8 0.8 0.8 0.4 16 22 35 37 41 mlg0603p0n8bt000 0.8 0.8 0.8 0.8 0.4 16 22 35 37 41 mlg0603p0n8ct000 0.9 0.9 0.9 0.9 0.9 17 22 35 37 41 mlg0603p0n9bt000 0.9 0.9 0.9 0.9 0.9 17 22 35 37 41 mlg0603p0n9ct000 1.0 1.0 1.0 1.0 1.0 16 21 33 36 40 mlg0603p1n0bt000 1.0 1.0 1.0 1.0 1.0 16 21 33 36 40 mlg0603p1n0ct000 1.0 1.0 1.0 1.0 1.0 16 21 33 36 40 mlg0603p1n0st000 1.1 1.1 1.1 1.1 1.1 17 23 36 38 43 mlg0603p1n1bt000 1.1 1.1 1.1 1.1 1.1 17 23 36 38 43 mlg0603p1n1ct000 1.1 1.1 1.1 1.1 1.1 17 23 36 38 43 mlg0603p1n1st000 1.2 1.2 1.2 1.2 1.2 18 24 38 40 45 mlg0603p1n2bt000 1.2 1.2 1.2 1.2 1.2 18 24 38 40 45 mlg0603p1n2ct000 1.2 1.2 1.2 1.2 1.2 18 24 38 40 45 mlg0603p1n2st000 1.3 1.3 1.3 1.3 1.3 17 22 34 36 40 mlg0603p1n3bt000 1.3 1.3 1.3 1.3 1.3 17 22 34 36 40 mlg0603p1n3ct000 1.3 1.3 1.3 1.3 1.3 17 22 34 36 40 mlg0603p1n3st000 1.4 1.4 1.4 1.4 1.4 18 23 36 39 43 mlg0603p1n4bt000 1.4 1.4 1.4 1.4 1.4 18 23 36 39 43 mlg0603p1n4ct000 1.4 1.4 1.4 1.4 1.4 18 23 36 39 43 mlg0603p1n4st000 1.5 1.5 1.5 1.5 1.5 17 22 33 35 39 mlg0603p1n5bt000 1.5 1.5 1.5 1.5 1.5 17 22 33 35 39 mlg0603p1n5ct000 1.5 1.5 1.5 1.5 1.5 17 22 33 35 39 mlg0603p1n5st000 1.6 1.6 1.6 1.6 1.6 17 22 33 35 38 mlg0603p1n6bt000 1.6 1.6 1.6 1.6 1.6 17 22 33 35 38 mlg0603p1n6ct000 1.6 1.6 1.6 1.6 1.6 17 22 33 35 38 mlg0603p1n6st000 1.7 1.7 1.7 1.7 1.7 17 22 33 35 39 mlg0603p1n7bt000 1.7 1.7 1.7 1.7 1.7 17 22 33 35 39 mlg0603p1n7ct000 1.7 1.7 1.7 1.7 1.7 17 22 33 35 39 mlg0603p1n7st000 1.8 1.8 1.8 1.8 1.8 17 22 34 35 39 mlg0603p1n8bt000 1.8 1.8 1.8 1.8 1.8 17 22 34 35 39 mlg0603p1n8ct000 1.8 1.8 1.8 1.8 1.8 17 22 34 35 39 mlg0603p1n8st000 1.9 1.9 1.9 1.9 1.9 18 24 36 38 42 mlg0603p1n9bt000 1.9 1.9 1.9 1.9 1.9 18 24 36 38 42 mlg0603p1n9ct000 1.9 1.9 1.9 1.9 1.9 18 24 36 38 42 mlg0603p1n9st000 2.0 2 2.0 2.0 2.0 19 23 35 37 41 mlg0603p2n0bt000 2.0 2 2.0 2.0 2.0 19 23 35 37 41 mlg0603p2n0ct000 2.0 2 2.0 2.0 2.0 19 23 35 37 41 mlg0603p2n0st000 2.1 2.1 2.1 2.1 2.1 18 23 34 36 39 mlg0603p2n1bt000 2.1 2.1 2.1 2.1 2.1 18 23 34 36 39 mlg0603p2n1ct000 2.1 2.1 2.1 2.1 2.1 18 23 34 36 39 mlg0603p2n1st000 2.2 2.2 2.2 2.2 2.3 18 23 35 36 40 mlg0603p2n2bt000 2.2 2.2 2.2 2.2 2.3 18 23 35 36 40 mlg0603p2n2ct000 2.2 2.2 2.2 2.2 2.3 18 23 35 36 40 mlg0603p2n2st000 2.3 2.3 2.3 2.4 2.4 18 22 33 35 38 mlg0603p2n3bt000 2.3 2.3 2.3 2.4 2.4 18 22 33 35 38 mlg0603p2n3ct000 2.3 2.3 2.3 2.4 2.4 18 22 33 35 38 mlg0603p2n3st000 product no. manufacturer 4291b+16197a agilent technologies
(12/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type electrical characteristics l, q frequency characteristics table please contact us for information on inductance tolerance, g (2%). measurement equipment ? equivalent measurement equipment may be used. l(nh)typ. q typ. part no. 500mhz 800mhz 1.8ghz 2.0ghz 2.4ghz 500mhz 800mhz 1.8ghz 2.0ghz 2.4ghz 2.4 2.4 2.4 2.4 2.4 16 21 31 33 36 mlg0603p2n4bt000 2.4 2.4 2.4 2.4 2.4 16 21 31 33 36 mlg0603p2n4st000 2.5 2.5 2.5 2.5 2.5 17 22 33 34 38 mlg0603p2n5bt000 2.5 2.5 2.5 2.5 2.5 17 22 33 34 38 mlg0603p2n5ct000 2.5 2.5 2.5 2.5 2.5 17 22 33 34 38 mlg0603p2n5st000 2.6 2.6 2.6 2.6 2.6 17 22 33 35 38 mlg0603p2n6bt000 2.6 2.6 2.6 2.6 2.6 17 22 33 35 38 mlg0603p2n6ct000 2.6 2.6 2.6 2.6 2.6 17 22 33 35 38 mlg0603p2n6st000 2.7 2.7 2.7 2.7 2.7 17 21 33 35 38 mlg0603p2n7bt000 2.7 2.7 2.7 2.7 2.7 17 21 33 35 38 mlg0603p2n7ct000 2.7 2.7 2.7 2.7 2.7 17 21 33 35 38 mlg0603p2n7st000 2.8 2.8 2.8 2.8 2.9 17 22 34 36 40 mlg0603p2n8bt000 2.8 2.8 2.8 2.8 2.9 17 22 34 36 40 mlg0603p2n8ct000 2.8 2.8 2.8 2.8 2.9 17 22 34 36 40 mlg0603p2n8st000 2.9 2.9 2.9 2.9 3.0 17 22 34 35 39 mlg0603p2n9bt000 2.9 2.9 2.9 2.9 3.0 17 22 34 35 39 mlg0603p2n9ct000 2.9 2.9 2.9 2.9 3.0 17 22 34 35 39 mlg0603p2n9st000 3.0 3 3.0 3.1 3.1 17 21 32 34 37 mlg0603p3n0bt000 3.0 3 3.0 3.1 3.1 17 21 32 34 37 mlg0603p3n0ct000 3.0 3 3.0 3.1 3.1 17 21 32 34 37 mlg0603p3n0st000 3.1 3.1 3.1 3.2 3.2 17 22 33 34 37 mlg0603p3n1bt000 3.1 3.1 3.1 3.2 3.2 17 22 33 34 37 mlg0603p3n1ct000 3.1 3.1 3.1 3.2 3.2 17 22 33 34 37 mlg0603p3n1st000 3.2 3.2 3.2 3.3 3.3 17 22 34 35 38 mlg0603p3n2bt000 3.2 3.2 3.2 3.3 3.3 17 22 34 35 38 mlg0603p3n2ct000 3.2 3.2 3.2 3.3 3.3 17 22 34 35 38 mlg0603p3n2st000 3.3 3.3 3.4 3.4 3.4 18 22 33 35 38 mlg0603p3n3bt000 3.3 3.3 3.4 3.4 3.4 18 22 33 35 38 mlg0603p3n3ct000 3.3 3.3 3.4 3.4 3.4 18 22 33 35 38 mlg0603p3n3st000 3.4 3.4 3.5 3.5 3.6 18 23 34 35 38 mlg0603p3n4bt000 3.4 3.4 3.5 3.5 3.6 18 23 34 35 38 mlg0603p3n4ct000 3.4 3.4 3.5 3.5 3.6 18 23 34 35 38 mlg0603p3n4st000 3.5 3.5 3.6 3.6 3.7 18 23 34 35 38 mlg0603p3n5bt000 3.5 3.5 3.6 3.6 3.7 18 23 34 35 38 mlg0603p3n5ct000 3.5 3.5 3.6 3.6 3.7 18 23 34 35 38 mlg0603p3n5st000 3.6 3.6 3.7 3.7 3.8 18 22 33 34 37 mlg0603p3n6bt000 3.6 3.6 3.7 3.7 3.8 18 22 33 34 37 mlg0603p3n6ct000 3.6 3.6 3.7 3.7 3.8 18 22 33 34 37 mlg0603p3n6st000 3.7 3.7 3.8 3.9 4.0 18 23 34 35 37 mlg0603p3n7bt000 3.7 3.7 3.8 3.9 4.0 18.0 23 34 35 37 mlg0603p3n7ct000 3.7 3.7 3.8 3.9 4.0 18.0 23 34 35 37 mlg0603p3n7st000 3.8 3.8 3.9 4.0 4.1 17.0 22 32 33 36 mlg0603p3n8bt000 3.8 3.8 3.9 4.0 4.1 17.0 22 32 33 36 mlg0603p3n8ct000 3.8 3.8 3.9 4.0 4.1 17.0 22 32 33 36 mlg0603p3n8st000 3.9 3.9 4.0 4.1 4.2 17.0 22 32 34 36 mlg0603p3n9bt000 3.9 3.9 4.0 4.1 4.2 17.0 22 32 34 36 mlg0603p3n9ct000 3.9 3.9 4.0 4.1 4.2 17.0 22 32 34 36 mlg0603p3n9st000 4.0 4.0 4.1 4.2 4.4 18.0 22 32 33 36 mlg0603p4n0bt000 4.0 4.0 4.1 4.2 4.4 18.0 22 32 33 36 mlg0603p4n0ct000 4.0 4.0 4.1 4.2 4.4 18.0 22 32 33 36 mlg0603p4n0st000 product no. manufacturer 4291b+16197a agilent technologies
(13/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type electrical characteristics l, q frequency characteristics table please contact us for information on inductance tolerance, g (2%). measurement equipment ? equivalent measurement equipment may be used. l(nh)typ. q typ. part no. 500mhz 800mhz 1.8ghz 2.0ghz 2.4ghz 500mhz 800mhz 1.8ghz 2.0ghz 2.4ghz 4.1 4.1 4.3 4.3 4.5 18.0 22 33 34 36 mlg0603p4n1bt000 4.1 4.1 4.3 4.3 4.5 18.0 22 33 34 36 mlg0603p4n1ct000 4.1 4.1 4.3 4.3 4.5 18.0 22 33 34 36 mlg0603p4n1st000 4.2 4.2 4.4 4.5 4.6 18.0 22 32 33 35 mlg0603p4n2bt000 4.2 4.2 4.4 4.5 4.6 18.0 22 32 33 35 mlg0603p4n2ct000 4.2 4.2 4.4 4.5 4.6 18 22 32 33 35 mlg0603p4n2st000 4.3 4.3 4.5 4.5 4.7 17 21 32 33 35 mlg0603p4n3st000 4.3 4.3 4.5 4.5 4.7 17 21 32 33 35 mlg0603p4n3ht000 4.3 4.3 4.5 4.5 4.7 17 21 32 33 35 mlg0603p4n3jt000 4.7 4.7 4.9 5.0 5.1 16 21 31 32 34 mlg0603p4n7st000 4.7 4.7 4.9 5.0 5.1 16 21 31 32 34 mlg0603p4n7ht000 4.7 4.7 4.9 5.0 5.1 16 21 31 32 34 mlg0603p4n7jt000 5.1 5.1 5.3 5.4 5.7 16 21 31 32 34 mlg0603p5n1st000 5.1 5.1 5.3 5.4 5.7 16 21 31 32 34 mlg0603p5n1ht000 5.1 5.1 5.3 5.4 5.7 16 21 31 32 34 mlg0603p5n1jt000 5.6 5.6 6.1 6.2 6.6 18 22 31 32 32 mlg0603p5n6st000 5.6 5.6 6.1 6.2 6.6 18 22 31 32 32 mlg0603p5n6ht000 5.6 5.6 6.1 6.2 6.6 18 22 31 32 32 mlg0603p5n6jt000 6.2 6.2 6.5 6.7 7.0 16 21 30 31 33 mlg0603p6n2st000 6.2 6.2 6.5 6.7 7.0 16 21 30 31 33 mlg0603p6n2ht000 6.2 6.2 6.5 6.7 7.0 16 21 30 31 33 mlg0603p6n2jt000 6.8 6.8 7.3 7.5 8.0 16 21 29 30 31 mlg0603p6n8ht000 6.8 6.8 7.3 7.5 8.0 16 21 29 30 31 mlg0603p6n8jt000 7.5 7.5 8.1 8.3 8.8 16 21 30 30 32 mlg0603p7n5ht000 7.5 7.5 8.1 8.3 8.8 16 21 30 30 32 mlg0603p7n5jt000 8.2 8.2 9.0 9.3 10.0 17 21 30 30 31 mlg0603p8n2ht000 8.2 8.2 9.0 9.3 10.0 17 21 30 30 31 mlg0603p8n2jt000 9.1 9.1 10.0 10.3 11.1 17 21 30 31 32 mlg0603p9n1ht000 9.1 9.1 10.0 10.3 11.1 17 21 30 31 32 mlg0603p9n1jt000 10 10 11 12 13 16 21 28 28 28 mlg0603p10nht000 10 10 11 12 13 16 21 28 28 28 mlg0603p10njt000 11 11 13 13 15 18 23 30 30 30 mlg0603p11nht000 11 11 13 13 15 18 23 30 30 30 mlg0603p11njt000 12 12 14 15 17 18 22 28 28 27 mlg0603p12nht000 12 12 14 15 17 18 22 28 28 27 mlg0603p12njt000 13 13 15 16 19 18 22 28 28 26 mlg0603p13nht000 13 13 15 16 19 18 22 28 28 26 mlg0603p13njt000 15 15 18 20 24 18 22 27 26 24 mlg0603p15nht000 15 15 18 20 24 18 22 27 26 24 mlg0603p15njt000 16 16 20 22 27 18 22 26 25 22 mlg0603p16nht000 16 16 20 22 27 18 22 26 25 22 mlg0603p16njt000 18 18 23 26 33 18 22 25 24 20 mlg0603p18nht000 18 18 23 26 33 18 22 25 24 20 mlg0603p18njt000 20 21 27 31 42 18 22 23 22 17 mlg0603p20nht000 20 21 27 31 42 18 22 23 22 17 mlg0603p20njt000 22 23 34 40 68 18 21 21 18 11 mlg0603p22nht000 22 23 34 40 68 18 21 21 18 11 mlg0603p22njt000 24 25 36 43 72 19 22 21 18 11 mlg0603p24nht000 24 25 36 43 72 19 22 21 18 11 mlg0603p24njt000 27 28 45 57 18 21 18 15 mlg0603p27nht000 27 28 45 57 18 21 18 15 mlg0603p27njt000 product no. manufacturer 4291b+16197a agilent technologies
(14/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type electrical characteristics l, q frequency characteristics table please contact us for information on inductance tolerance, g (2%). measurement equipment ? equivalent measurement equipment may be used. l(nh)typ. q typ. part no. 500mhz 800mhz 1.8ghz 2.0ghz 2.4ghz 500mhz 800mhz 1.8ghz 2.0ghz 2.4ghz 30 32 59 18 21 15 mlg0603p30nht000 30 32 59 18 21 15 mlg0603p30njt000 33 36 68 15 17 11 mlg0603p33nht000 33 36 68 15 17 11 mlg0603p33njt000 37 39 16 17 mlg0603p36nht000 37 39 16 17 mlg0603p36njt000 40 43 15 17 mlg0603p39nht000 40 43 15 17 mlg0603p39njt000 44 48 15 16 mlg0603p43nht000 44 48 15 16 mlg0603p43njt000 48 53 15 16 mlg0603p47nht000 48 53 15 16 MLG0603P47NJT000 53 59 15 16 mlg0603p51nht000 53 59 15 16 mlg0603p51njt000 58 66 15 15 mlg0603p56nht000 58 66 15 15 mlg0603p56njt000 65 76 15 15 mlg0603p62nht000 65 76 15 15 mlg0603p62njt000 71 82 15 15 mlg0603p68nht000 71 82 15 15 mlg0603p68njt000 79 97 14 13 mlg0603p75nht000 79 97 14 13 mlg0603p75njt000 87 109 14 13 mlg0603p82nht000 87 109 14 13 mlg0603p82njt000 99 132 13 12 mlg0603p91nht000 99 132 13 12 mlg0603p91njt000 110 152 14 12 mlg0603pr10ht000 110 152 14 12 mlg0603pr10jt000 126 211 13 9 mlg0603pr11ht000 126 211 13 9 mlg0603pr11jt000 151 12 mlg0603pr12ht000 151 12 mlg0603pr12jt000 product no. manufacturer 4291b+16197a agilent technologies
(15/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type electrical characteristics l frequency characteristics graph (example) measurement equipment ? equivalent measurement equipment may be used. 10 100 1000 10000 0 1000 100 10 1 frequency ( mhz ) inductance ( nh ) r12 r10 82n 68n 56n 47n 39n 33n 27n 22n 18n 15n 12n 10n 8n2 6n8 5n6 4n7 3n9 3n3 2n7 2n2 1n8 1n5 1n2 1n0 product no. manufacturer e4991a+16197a agilent technologies
(16/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type electrical characteristics q frequency characteristics graph (example) measurement equipment ? equivalent measurement equipment may be used. 0 10 20 30 40 50 q 10 100 1000 10000 frequency ( mhz ) r12 r10 27n 22n 18n 15n 12n 10n 8n2 6n8 5n6 4n7 3n9 3n3 2n7 1n8 1n2 1n0 39n 56n 47n 68n 82n 33n 1n5 2n2 product no. manufacturer e4991a+16197a agilent technologies
(17/17) inductors 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlg0603p type packaging style reel dimensions tape dimensions 1.0 ?180 2.0 2.0 0.5 ?13 0.2 ?21 0.8 ?60min. 14.4max. dimensions in mm 8.4 +2.0 C0.0 8.00.3 3.50.05 1.750.1 4.0 0.1 1.5 +0.1 C0.0 sprocket hole cavity a kb 2.0 0.05 2.0 0.05 160min. taping 200min. 300min. drawing direction ty p e a b k mlg0603p 0.680.05 0.380.05 0.5 max.

▲Up To Search▲

Price & Availability of MLG0603P47NJT000

	To Download MLG0603P47NJT000 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .